Pump & Lubricants
Moresco Hydraulic Fluids
Hydraulic fluids are pressure transfer mediums used to transfer the energy stored by way of a hydraulic pump to the hydraulic actuators of cylinders, motors, and other similar devices. To provide precise, accurate, and stable operation of hydraulic equipment, these fluids must have lubricating properties, rust-prevention and corrosion-prevention properties, special temperature and viscosity properties, stability properties, foam suppression properties, and similar properties.
Among these products, HYDOL, our fire resistant hydraulic fluid, is used in hydraulic equipment such as die-cast machines used in the manufacturing of aluminum automotive parts, steel works, and presses. HYDOL protects plant equipment from fires.
HYDOL HAW Series
For hydraulic equipment that handles melted metal such as steel working equipment and die-cast machines, a major fear is the hydraulic fluid catching on fire. To prevent plant fires before they happen, fire resistant hydraulic fluid, which does not catch on fire easily, is used. Among all fire resistant hydraulic fluids, water-glycol type hydraulic fluid exhibits excellent flame resistance as well as having a good balance among all other hydraulic fluid properties.
HAW Red clear liquid : Water-glycol hydraulic fluid with a flame-retardant and high lubricity. Available in a high-pressure area of 14-25MP discharge pressure.
HYDOL AW Series
These products have excellent anti wear properties. A general use type, anti wear type, and high viscosity index type are available. Various viscosity grades are available for each type.
AW-series : Wear resistance hydraulic fluid.
Among these products, HYDOL, our fire resistant hydraulic fluid, is used in hydraulic equipment such as die-cast machines used in the manufacturing of aluminum automotive parts, steel works, and presses. HYDOL protects plant equipment from fires.
HYDOL HAW Series
For hydraulic equipment that handles melted metal such as steel working equipment and die-cast machines, a major fear is the hydraulic fluid catching on fire. To prevent plant fires before they happen, fire resistant hydraulic fluid, which does not catch on fire easily, is used. Among all fire resistant hydraulic fluids, water-glycol type hydraulic fluid exhibits excellent flame resistance as well as having a good balance among all other hydraulic fluid properties.
HAW Red clear liquid : Water-glycol hydraulic fluid with a flame-retardant and high lubricity. Available in a high-pressure area of 14-25MP discharge pressure.
HYDOL AW Series
These products have excellent anti wear properties. A general use type, anti wear type, and high viscosity index type are available. Various viscosity grades are available for each type.
AW-series : Wear resistance hydraulic fluid.
Download
Produk Lainnya
Comprising of an enamel finish and a heavy-gauge, seamless metal body, these oil cans are suited for heavy-duty applications. Each can has a positive force feed brass pump and valve and is supplied with both rigid metal and flexible nylon threaded spouts. Finished in a red colour.
Features and Benefits
• Enamel finish provides additional protection against wear and tear
• Heavy gauge construction makes for a robust and resilient product
• Supplied with one metal and one flexible nylon spout for versatility
• Available in a range of sizes to suit your requirements
Typical Applications
• Automotive
• Construction
Features and Benefits
• Enamel finish provides additional protection against wear and tear
• Heavy gauge construction makes for a robust and resilient product
• Supplied with one metal and one flexible nylon spout for versatility
• Available in a range of sizes to suit your requirements
Typical Applications
• Automotive
• Construction
Hot dip protective plastic coating moulds around the component or tool to provide 100% coverage and protect against impact and corrosion.
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
Die Realasing Fluids | GRAPHACE
Die casting is a casting method in which molten metals under high pressure are poured into molds and hardened. Our GRAPHACE series of die casting mold releasing lubricants is crucial for releasing heated metals from their molds. GRAPHACE brand die lubricants are used in die cast machines to cast aluminum, magnesium, and zinc parts, which results in better quality parts, improvements to plant productivity and a better working environment.
MS-1 White : liquid Excellent seizure resistance. Available for wide range of machine size at high dilution. Also available as anti-seize agent at low dilution.
GL-6300 Milky white : liquid It is a newly designed release agent considering the adhesion efficiency of release agent components.
Plunger Lubricants | NEOCASTER
During the die casting process, plunger lubricant is necessary to lubricate the sleeves and tips that force the molten metal into the molds. Our NEOCASTER brand plunger lubricant is used in the casting of aluminum parts for automobiles, motorcycles, mobile phones, and similar objects. Using the NEOCASTER plunger lubricant has proven to increase the life of the tip and the shot sleeve as well as improve the casting quality.
PWS-850 : Yellowish brown Good wettability to the metal surface. Stable lubricity at high temperature.
PW-50 : Milky white liquid Available for small and midium-sized machine.
B-200R : Black General purpose type.
RE-77 : Milky white liquid Suitable for small and medium-sized machine.
Die casting is a casting method in which molten metals under high pressure are poured into molds and hardened. Our GRAPHACE series of die casting mold releasing lubricants is crucial for releasing heated metals from their molds. GRAPHACE brand die lubricants are used in die cast machines to cast aluminum, magnesium, and zinc parts, which results in better quality parts, improvements to plant productivity and a better working environment.
MS-1 White : liquid Excellent seizure resistance. Available for wide range of machine size at high dilution. Also available as anti-seize agent at low dilution.
GL-6300 Milky white : liquid It is a newly designed release agent considering the adhesion efficiency of release agent components.
Plunger Lubricants | NEOCASTER
During the die casting process, plunger lubricant is necessary to lubricate the sleeves and tips that force the molten metal into the molds. Our NEOCASTER brand plunger lubricant is used in the casting of aluminum parts for automobiles, motorcycles, mobile phones, and similar objects. Using the NEOCASTER plunger lubricant has proven to increase the life of the tip and the shot sleeve as well as improve the casting quality.
PWS-850 : Yellowish brown Good wettability to the metal surface. Stable lubricity at high temperature.
PW-50 : Milky white liquid Available for small and midium-sized machine.
B-200R : Black General purpose type.
RE-77 : Milky white liquid Suitable for small and medium-sized machine.
Cantilever pumps are ideal for moving abrasive materials and slurries, as only a portion of the pump is located under the fluid. The seals, bearings, bushings, and suction check valves are all outside of the liquid, preventing the material from degrading or interfering with them.
Our cantilever pumps are designed by our engineering team that specializes in handling the toughest pumping jobs. They set the standard for pumping slurries and abrasive materials.
Our cantilever pumps are designed by our engineering team that specializes in handling the toughest pumping jobs. They set the standard for pumping slurries and abrasive materials.