Produk

The CP8854 combines the performance of Twin Hammer Mechanism technology with the advantages of an advanced brushless electric motor. This innovation performs as well as air tools in terms of lightweight, compact design, vibration, sound, power, and offers the mobility advantage of cordless tools. It provides a built-in SHUT OFF feature for (80 ft.lbs. / ≈ 120 Nm). It has a SNUGGING feature to eliminate hand tightening. No more overtightening. CP8854 series comes in 2 styles 1/2'' short anvil and 1/2" 2'' long anvil. Available as a tool only or in a kit with two batteries and one charger.

The J100 Series are general purpose HSS straight shank drills with a black oxide finish. Ideal for applications involving steel (including cast steel) cast iron (including malleable cast iron) as well as nickel, brass aluminium alloys and graphite. Their 118° point allows for precise hole alignment and reliable cutting performance whilst the black oxide coating helps reduce heat by retaining coolant on the tool surface. The coating also helps reduce the risk of the tool staining.

Features and Benefits
• High speed steel construction for increased tool durability
• Point angle of 118° for precise holemaking and precision cutting
• Black oxide coating helps aid chip flow, reduce heat and prevent staining
• Ideal for applications involving steel, iron, nickel, brass, aluminium alloy and graphite

Typical Applications
• Cutting and drilling
• Ferrous materials
• Steel
• Iron
• Nickel
• Brass
• Aluminium alloy
• Graphite

Notes
• Available in sizes 0.25mm -20.00mm

Standards
• Manufactured to BS 328/DIN338RN

No pipetting, no drips, no timing: With the Dräger DrugTest 5000, a drug test is carried out simply and quickly. The collected saliva sample can be analysed immediately – for an accurate result on the spot.

York non-woven fibre hand pads are ideal for cleaning, blending and finishing applications. They are available in a range grades from non abrasive to coarse to suit any application. They are supplied in packs of 10 to ensure they can get you through any project.

Features and Benefits
• Available in a range of grades to suit any application
• Supplied in packs of 10 to ensure they can get you through any project

Hydraulic fluids are pressure transfer mediums used to transfer the energy stored by way of a hydraulic pump to the hydraulic actuators of cylinders, motors, and other similar devices. To provide precise, accurate, and stable operation of hydraulic equipment, these fluids must have lubricating properties, rust-prevention and corrosion-prevention properties, special temperature and viscosity properties, stability properties, foam suppression properties, and similar properties.

Among these products, HYDOL, our fire resistant hydraulic fluid, is used in hydraulic equipment such as die-cast machines used in the manufacturing of aluminum automotive parts, steel works, and presses. HYDOL protects plant equipment from fires.

HYDOL HAW Series

For hydraulic equipment that handles melted metal such as steel working equipment and die-cast machines, a major fear is the hydraulic fluid catching on fire. To prevent plant fires before they happen, fire resistant hydraulic fluid, which does not catch on fire easily, is used. Among all fire resistant hydraulic fluids, water-glycol type hydraulic fluid exhibits excellent flame resistance as well as having a good balance among all other hydraulic fluid properties.

HAW Red clear liquid : Water-glycol hydraulic fluid with a flame-retardant and high lubricity. Available in a high-pressure area of 14-25MP discharge pressure.

HYDOL AW Series

These products have excellent anti wear properties. A general use type, anti wear type, and high viscosity index type are available. Various viscosity grades are available for each type.

AW-series : Wear resistance hydraulic fluid.

These extra-heavy-duty rotational moulded IBC (intermediate bulk container) spill pallets are for single or double IBC storage applications. 100% polyethylene construction, they're designed for total flexibility and ease of positioning.

Features and Benefits
• Contains spills to prevent accidents and waterway contamination
• Made from durable polyethylene to protect against the elements
• Fitted with grids for added support
• Forklift pockets in the base make for easy transport
• Corrosion-free and suitable for containing corrosive chemicals
• Removable decking assists cleaning
• Reusable for a cost-effective solution to spill control and chemical storage

Ideally adapted for working in restricted areas, this cordless impact wrench is lightweight (2.4 lbs - 1.1 Kg) and compact (6.3 in - 161 mm length). Its high power (84 ft.lbs - 115 Nm max torque) in reverse offers performance and durability. The SIDE 2 SIDE Single-hand forward / reverse operation and built-in LED are convenient for every day general mechanical applications in workshops. The CP8818 series is available as a bare tool or in packs with two batteries and one charger.

IWS100X - 1" square drive. Suitable for industrial and commercial production and assembly applications. Side handle for two-handed operation. Top mounted spring balance loop. Easy to use forward/reverse switch and three position power regulator. Top venting exhaust. Oiling points for daily maintenance.

Bolt Capacity: M33
Working torque: 2,030 Nm
Maximum torque: 2,300Nm
Safe working pressure: 6.2bar / 90psi.
Air inlet thread: 1/2" NPT.
Minimum air hose size (ID): 1/2" (13mm).
Air pressure: 6.3bar/90 psi.
Air consumption: 7.0 cfm.
Sound pressure level: 96 dBA.
Sound power level: 101.67 dBA.
Vibration level: 6.0 m/s².
Overall length: 448mm.

The Dräger Interlock® 7000 is an alcohol ignition interlock device (AIID) which prevents a person under the influence of alcohol from starting the vehicle. The Interlock® 7000 has a quick start-up time. Additionally, the device can be equipped with a camera, a GPS and/or a mobile data transfer module, according to the specific customer requirements.

The J100 Series are general purpose HSS straight shank drills with a black oxide finish. Ideal for applications involving steel (including cast steel) cast iron (including malleable cast iron) as well as nickel, brass aluminium alloys and graphite. Their 118° point allows for precise hole alignment and reliable cutting performance whilst the black oxide coating helps reduce heat by retaining coolant on the tool surface. The coating also helps reduce the risk of the tool staining.

Features and Benefits
• High speed steel construction for increased tool durability
• Point angle of 118° for precise holemaking and precision cutting
• Black oxide coating helps aid chip flow, reduce heat and prevent staining
• Ideal for applications involving steel, iron, nickel, brass, aluminium alloy and graphite

Typical Applications
• Cutting and drilling
• Ferrous materials
• Steel
• Iron
• Nickel
• Brass
• Aluminium alloy
• Graphite

Notes
• Available in sizes 0.25mm -20.00mm

Standards
• Manufactured to BS 328/DIN338RN

Fluke’s two-pole voltage and continuity testers are built to work the way you work. They give you the best combination of safety, ease-of-use and fast answers available anywhere.

• Designed according to IEC EN 61243-3:2014 to verify the absence of voltage – even with discharged batteries.

• CAT IV 600 V, CAT III 690 V safety rating

• With 4 ways to indicate the presence of voltage – LED indicator, LCD display, audible tone or tactile feedback, always know if hazardous voltage is present (digital display on T130, T150, vibration indicator on T110, T130, T150)

NEOVAC is well-known as a synonym for high quality vacuum pump oil. We have received endorsements of NEOVAC as the oil used by many vacuum pump manufacturers due to the high level of trust placed in NEOVAC's performance. NEOVAC is used in vacuum equipment in applications such as semiconductors, silicon wafers, vacuum deposition, heat treatment, and packaging and contributes to productivity improvements.

NEOVAC MR Series

Rotary pump vacuum oil is used with the purposes of lubrication and the preservation of airtight seals. It has a low steam pressure, suitable viscosity, and is difficult to emulsify (it has anti-emulsification properties). In other words, it easily separates from water and removes water.

MR-100 : Standard for small pump
MR-200 : Standard for small pump
MR-250 : Standard for small pump
MR-200A : Improved heat and oxidation. Moisture suction is supported
MR-250A : Improved heat and oxidation. Moisture suction is supported. For large pump

NEOVAC SX & SY

Diffusion pump vacuum oil is sprayed either as molecules or as a steam and is used to obtain a vacuum state. It is necessary for these oils to be chemically stable such as by having low steam pressures, by not being transformed due to heat (heat resistance), and by not reacting easily with oxygen (oxidation resistance).

SX : For surface treatment equipment. (vapor deposition, sputter, heat treatment)
SY : For surface treatment equipment. (vapor deposition, sputter, heat treatment)