Pump & Lubricants
Kennedy Hydraulic Connector, 4 Jaw, 1/8" BSP(T), Steel
This 1/8" BSP threaded, 4 jaw hydraulic connector is an effective way of allowing for the controlled flow of lubricants. Securely fastens the grease nipple when in use to ensure minimal slippage.
Features and Benefits
• Manufactured from steel for durability
• Securely grips the grease nipple while in use to control the flow of the lubricant
• Textured in places for easy gripping even with oily or greasy hands
Typical Applications
• Automotive
• Engineering
• Mechanics
Features and Benefits
• Manufactured from steel for durability
• Securely grips the grease nipple while in use to control the flow of the lubricant
• Textured in places for easy gripping even with oily or greasy hands
Typical Applications
• Automotive
• Engineering
• Mechanics
Download
Products Lainnya
Hot dip protective plastic coating moulds around the component or tool to provide 100% coverage and protect against impact and corrosion.
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
Suitable for lubricants, diesel and non-corrosive liquids, this lever pump is constructed from a zinc chrome finish steel and is completed with a telescopic suction tube. Suitable for container sizes 60 and 205 litres, the innlet on the pump is 2" BSP and M59 x 5 male thread.
Features and Benefits
• Manufactured from steel for durability
• Zinc chrome finish protects against corrosion and wear and tear
• Can be used with both 60 and 205 litre containers making it a versatile product
• Is compatible with non-corrosive liquids and most lubricants
• Telescopic suction tube allows you to adjust the tube to suit your desired container
Typical Applications
• Automotive
• Engineering
Features and Benefits
• Manufactured from steel for durability
• Zinc chrome finish protects against corrosion and wear and tear
• Can be used with both 60 and 205 litre containers making it a versatile product
• Is compatible with non-corrosive liquids and most lubricants
• Telescopic suction tube allows you to adjust the tube to suit your desired container
Typical Applications
• Automotive
• Engineering
Our horizontal multistage centrifugal pumps are made of multiple Discpacs, which feed into one another. These stages allow for higher levels of control over the output pressure.
RP250
Used for dispensing lubricants and disel, this cast iron pump with a steel suction tube and spout is the easy way to control the flow of said liquids. Suitable for container size of 200 litres, the pump possesses an inlet of 2" BSP and M59 x 5 male thread.
Features and Benefits
• Cast iron pump with steel suction tube and spout making for a hardy product
• Suited for use on a 200 lite capacity barrel
• With a 980mm tube to easily dispense liquids when necessary
Typical Applications
• Suited for controlling the flow of fluids in a 200 litre barrel
Used for dispensing lubricants and disel, this cast iron pump with a steel suction tube and spout is the easy way to control the flow of said liquids. Suitable for container size of 200 litres, the pump possesses an inlet of 2" BSP and M59 x 5 male thread.
Features and Benefits
• Cast iron pump with steel suction tube and spout making for a hardy product
• Suited for use on a 200 lite capacity barrel
• With a 980mm tube to easily dispense liquids when necessary
Typical Applications
• Suited for controlling the flow of fluids in a 200 litre barrel